The real difference is diaphragm material, not throat size
Both DS18 drivers here share a 2" throat and 8-ohm impedance, so they bolt to the same kind of horn and present a similar load to your amplifier. The meaningful split is the voice coil and diaphragm: the PRO-DN22TI.8 uses a 2" titanium voice coil, while the PRO-DN24PH.8 uses a 4" phenolic voice coil. That choice drives the frequency response, power ratings, and sensitivity differences below.
Use this comparison to decide which driver suits your intended passband and power level—not as a claim that one material is universally better.
Spec-by-spec: PRO-DN22TI.8 vs PRO-DN24PH.8
- Voice coil and diaphragm: PRO-DN22TI.8: 2" titanium voice coil. PRO-DN24PH.8: 4" phenolic voice coil. The larger phenolic coil is paired with a phenolic diaphragm for deeper tones and a wider response range, per DS18.
- Frequency response: PRO-DN22TI.8: 630Hz–20kHz. PRO-DN24PH.8: 400Hz–12.5kHz. The titanium driver reaches higher; the phenolic driver starts lower.
- Power handling (AES / Program / Peak): PRO-DN22TI.8: 200W / 400W / 800W. PRO-DN24PH.8: 250W / 500W / 1000W. The phenolic model carries higher ratings across all three figures.
- Sensitivity: PRO-DN22TI.8: 111 dB. PRO-DN24PH.8: 107.5 dB. The titanium driver is rated more sensitive, meaning it should play louder for a given input.
- Magnet: Both use a neodymium magnet. The PRO-DN22TI.8 is described as lightweight yet powerful; the PRO-DN24PH.8 also uses neodymium.
- Mounting: Both are bolt-on with a 2" throat. The PRO-DN22TI.8 has a 4.4" overall diameter and 2.2" depth; depth for the PRO-DN24PH.8 is not stated in the supplied information.
Evidence for the titanium option
- 2" Throat Bolt-On Compression Driver 2" Titanium Voice Coil 8-Ohm: DS18 PRO-DN22TI.8: 2" titanium voice coil, 8-ohm, 630Hz–20kHz, 111 dB sensitivity, AES 200W / Program 400W / Peak 800W. These figures show a driver tuned for extended highs and high sensitivity—useful when you want strong output from modest power.

2" Throat Bolt-On Compression Driver 2" Titanium Voice Coil 8-Ohm - 2" Throat Bolt-On Compression Driver 2" Titanium Voice Coil 8-Ohm: Compact dimensions: 4.4" overall diameter and 2.2" depth, with bolt-on installation. The stated depth helps you check clearance before committing to a mounting location.
Evidence for the phenolic option
- 2” Throat Bolt-On Compression Driver 500 Watts With 4” Phenolic Voice Coil And Neodymium Magnet: DS18 PRO-DN24PH.8: 4" phenolic voice coil, 8-ohm, 400Hz–12.5kHz, 107.5 dB sensitivity, AES 250W / Program 500W / Peak 1000W. The lower frequency start and higher power ratings suit builds that need midrange coverage and more headroom.

2” Throat Bolt-On Compression Driver 500 Watts With 4” Phenolic Voice Coil And Neodymium Magnet - 2” Throat Bolt-On Compression Driver 500 Watts With 4” Phenolic Voice Coil And Neodymium Magnet: 2" throat diameter and bolt-on installation type, described by DS18 as guaranteeing a secure fit. Confirms it mounts like the titanium model, so horn compatibility is not the deciding factor between them.
Which one fits your build?
Choose the PRO-DN22TI.8 if your priority is high-frequency extension and efficiency: its 630Hz–20kHz range and 111 dB sensitivity make it a strong candidate for systems crossing over above roughly 630Hz where you want maximum output per watt.
Choose the PRO-DN24PH.8 if you need to cover down to 400Hz or want higher power ratings. Its 400Hz–12.5kHz response and 250W AES rating give more midrange reach and headroom, at the cost of top-end extension and sensitivity.
Both are 8-ohm bolt-on 2" throat drivers, so the horn and amplifier compatibility question is the same for either. The decision comes down to passband and power, not mounting.
What the supplied information does not settle
The catalog does not state recommended crossover points, enclosure volumes, or amplifier power windows for either driver—only the frequency response and power ratings above. It also does not provide depth for the PRO-DN24PH.8, so verify clearance separately if space is tight.
No listening tests or measured performance data are supplied, so treat sensitivity and frequency response as manufacturer specifications rather than demonstrated in-room results. Use them to narrow the choice, then confirm fit and crossover settings in your own system.



