Free US Shipping on Orders Over $99
Terug naar blog
Handleidingen 2026-11-17 Official DS18 Pro Audio Store - Speakers, Subwoofers, Amps & More! 0 weergaven

Reconing a CARBON18.1D Subwoofer: What the Kit Covers

Reconing a CARBON18.1D Subwoofer: What the Kit Covers

A practical look at the CARBON18.1DRCK recone kit: what it restores, the glues DS18 recommends, and how to plan a high excursion subwoofer rebuild.

What a recone kit actually replaces

A recone kit is a way to keep a subwoofer frame in service instead of replacing the whole driver. The CARBON18.1DRCK recone kit is built for the CARBON18.1D high excursion subwoofer and, per DS18, brings the sub back to its original tone and clarity while retaining its power.

That description matters because it sets the scope: the kit is for rebuilding the moving assembly on your existing frame, not for changing the subwoofer into a different design. If you are weighing a high excursion subwoofer repair against a new purchase, the kit is the option that preserves the CARBON18.1D platform you already own.

The kit and the driver it serves

  • Recone Kit for High Excursion Subwoofer CARBON18.1D: Recone Kit for High Excursion Subwoofer CARBON18.1D (CARBON18.1DRCK); sealer and glue are required for installing onto your existing frame. Confirms the kit is matched to the CARBON18.1D and that installation depends on supplies you must have on hand.
    Recone Kit for High Excursion Subwoofer CARBON18.1D
    Recone Kit for High Excursion Subwoofer CARBON18.1D
  • 18" High Excursion Subwoofer with Carbon Fiber Cone | 3500W RMS / 7000W Peak | Dual 1-Ohm Voice Coil: CARBON18.1D: 3500W RMS / 7000W MAX, impedance 1+1 ohm, sensitivity 85dB, frequency response 10-200Hz, carbon fiber cone with aluminum voice coil. These are the ratings the rebuilt sub is meant to retain, so they are the reference point for your amplifier and enclosure plan.
    18" High Excursion Subwoofer with Carbon Fiber Cone | 3500W RMS / 7000W Peak | Dual 1-Ohm Voice Coil
    18" High Excursion Subwoofer with Carbon Fiber Cone | 3500W RMS / 7000W Peak | Dual 1-Ohm Voice Coil

Supplies DS18 names before you start

The product information is specific about adhesives: sealer and glue are required for installing the kit onto your existing frame, and DS18 recommends CA glue for the dust cap and E6000 for the surround. Treat those as the starting point for your supply list rather than improvising with whatever is in the garage.

Beyond those two named adhesives, the supplied information does not list a full tool or consumable checklist. That is a planning gap, not a reason to guess. Source the sealer and the recommended glues first, then confirm any other materials with DS18 support before you disassemble a working sub.

A sensible order for the rebuild

The catalog does not publish a step-by-step procedure, so the sequence below is planning guidance around the confirmed requirements, not a manufacturer instruction sheet. Stop and ask DS18 for the service procedure if any stage is unclear.

  1. 1. Confirm the driver and the kit match: Check that your sub is the CARBON18.1D and that you have the CARBON18.1DRCK kit. The kit is named for that model specifically.
  2. 2. Gather sealer and the recommended glues: CA glue for the dust cap and E6000 for the surround are the adhesives DS18 names. Have them before you open up the sub.
  3. 3. Plan the frame work around your existing basket: The kit installs onto your existing frame, so the frame stays and the moving parts are what get renewed.
  4. 4. Check your amplifier plan before reassembly: The CARBON18.1D is a dual 1-ohm (1+1 ohm) sub rated 3500W RMS / 7000W MAX. Make sure the wiring and power you plan to feed it still suit those figures after the rebuild.
  5. 5. Let the adhesives set before you play loud: The supplied information does not give cure times or a break-in schedule. Follow the adhesive makers' directions and ask DS18 if you need guidance specific to the kit.

Why the carbon fiber and aluminum parts matter here

DS18 describes the CARBON18.1D as using a carbon fiber cone with an aluminum voice coil, and credits the design with added strength and clarity plus improved heat dissipation so you can play louder and longer. Those are manufacturer claims about the design, not a measured before-and-after result for a recone.

The practical takeaway is narrower: the recone kit is intended to restore the original tone and clarity and retain the sub's power. It is not sold as an upgrade path to a different sound. If you want a different character, that is a driver-selection question rather than a recone question.

Recone or replace?

  • Recone with the CARBON18.1DRCK: Keeps your existing frame and targets the original tone, clarity and power of the CARBON18.1D. Requires sealer, CA glue and E6000, plus the labor of the rebuild.
  • Buy a new CARBON18.1D: A fresh driver arrives assembled. This is the simpler route if your frame is damaged or you would rather not handle adhesives.
  • What the catalog does not settle: The supplied records do not include a condition checklist for deciding whether a frame is reusable. Have that judged before you commit to a rebuild.

Set expectations before the first play

The CARBON18.1D's 10-200Hz response and 85dB sensitivity describe the driver, not what you will hear from a rebuilt unit on day one. The supplied information makes no claim about audible improvement from reconing, only restoration.

Keep the 1+1 ohm impedance in mind when you reconnect. A dual 1-ohm sub gives you wiring options, and the final load your amplifier sees depends on how you configure it. Recheck that against your amp's rating before you turn up the volume, and treat the 3500W RMS figure as the number to plan around rather than the peak rating.

Gerelateerde artikelen

Customer Service
Home
Producten
Winkelwagen
Profiel